美国的斜齿轮图纸的英文,谁能帮忙翻译下,不胜感激!

yang13564

1.
Quality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.

2.
FOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379

3.
CROWN DRIVEN GWAR ONLY

4.
NORMAL PRESSURE ANGLE 20”

5.
0 L1 L: `# w2 t3 f, {% u/ q1 HNORMAL DIAMETRAL PITCH 8

6.
NORMAL CIRAULAR PITCH 0.3927

7.
& I# o9 V# d: S, {6 y+ K) MHELIX ANGLE:16.6011

8.
5 `- ^9 p2 t W: EBACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS

9.
MATERIAL: AISI 8620

10.
CASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS
TO BE 25-40 RC.

11.
% E) [2 C6 P# l; S- u! s' _7 kRETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.

12.
EACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.

13.
! g# s& s9 ?1 ?0 B3 O6 o7 SREMOVE ALL CHIPS FROM TAPPED HOLES.

NUMBER OF TEETH

HAND OF HELIX

LEAD OF HELIX

PIRTCH DIAMETER

BASE CIRCLE DIAMETER

ADDENDUM

WHOLE DEPTH

TRANSVERSE CIRCULAR

TOOTH THICKNESS WO/BL

NORMAL CIRCULAR

TOOTH THICKNESS WO/BL

yang13564

Y: A' b+ r ^2 m: H: I O. V
没有人翻译,找到了资料,不知道对不对!望高手出来指正!
* O5 w4 \) s0 U# h0 Z1 z? 齿轮制造标准和精度等级：ANSI/AGMA 2000-A88，精度12级，全深，全倒角。
, }4 \9 i* E" X$ F? 齿向、齿形修缘和渐开线轮廓公差按54773379图纸规定。
? 仅驱动齿轮鼓形修整。
? 齿形压力角20º
) \- T7 a; F, o" |? 节径DP=10
? 齿距：0.3142
: H7 e3 z0 H* f* q9 w1 k? 螺旋角：15.9355º
# v* D! S/ z$ m: Q( `. t? 在齿轮啮合中心距5.5118”上，侧隙要求在0.006” ~0.010”之间。
? 齿轮材料：AISI 8620
? 渗碳层0.025”~0.040”有效深度，表面硬度为57~61Rc，芯部硬度25~40Rc。
, V3 F, x1 E) h Z? 残余奥氏体最大5%目测检查。
! v0 ~; n. ~" F% ^& ^. A* ]? 每个周转盒内只能装一个齿轮组，周转盒外标记齿轮组图号，齿轮表面须按图示部位用电蚀法标记零件号和供货商代码，字高约0.25。
? 攻丝后，去除螺纹孔内的铁屑。

qvzhiwei

楼上玩意的好专业，佩服！！！

another

二楼挺专业的···感觉还不错，很值得学习。