美国的斜齿轮图纸的英文,谁能帮忙翻译下,不胜感激!

yang13564

1.
Quality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.

2.
FOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379

3.
5 n  k$ j4 ^! YCROWN DRIVEN GWAR ONLY

4.
% N6 {; P, W% a* P/ xNORMAL PRESSURE ANGLE 20”

5.
  ]1 X7 s' F# T0 b% _NORMAL DIAMETRAL PITCH 8

6.
1 P# `2 L0 i/ ^. O& ANORMAL CIRAULAR PITCH 0.3927

7.
HELIX ANGLE:16.6011

8.
BACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS

9.
MATERIAL: AISI 8620

10.
CASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS
5 m0 W: Z& w& Z  r0 F& ^TO BE 25-40 RC.

11.
8 C, Q3 U- b4 c7 R& _RETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.

12.
/ e% P5 m4 R$ ~1 q8 [EACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.

13.
/ u0 n" Z2 A1 U- ]2 VREMOVE ALL CHIPS FROM TAPPED HOLES.

NUMBER OF TEETH

HAND OF HELIX

LEAD OF HELIX

PIRTCH DIAMETER

BASE CIRCLE DIAMETER

ADDENDUM

WHOLE DEPTH

TRANSVERSE CIRCULAR

TOOTH THICKNESS WO/BL

NORMAL CIRCULAR

TOOTH THICKNESS WO/BL

another

二楼挺专业的···感觉还不错，很值得学习。

qvzhiwei

楼上玩意的好专业，佩服！！！

yang13564

+ c4 d  a3 _4 o6 g* n6 ?没有人翻译,找到了资料,不知道对不对!望高手出来指正!
1 x8 I! ]8 _: Y7 l        齿轮制造标准和精度等级：ANSI/AGMA 2000-A88，精度12级，全深，全倒角。
3 m2 d9 F% v* z9 T/ I        齿向、齿形修缘和渐开线轮廓公差按54773379图纸规定。
2 p* m1 d3 N8 L$ G: {, F        仅驱动齿轮鼓形修整。
        齿形压力角20º
; o- ~. ]0 q" Q$ h        节径DP=10
- j+ U9 G3 d, @! C& t        齿距：0.3142
        螺旋角：15.9355º
        在齿轮啮合中心距5.5118”上，侧隙要求在0.006” ~0.010”之间。
/ k# Q+ @* M2 ]# }+ P        齿轮材料：AISI 8620
! ~5 o5 h) i: Q. E$ D. G        渗碳层0.025”~0.040”有效深度，表面硬度为57~61Rc，芯部硬度25~40Rc。
' [3 @* U8 @% D0 x- C* z. |        残余奥氏体最大5%目测检查。
        每个周转盒内只能装一个齿轮组，周转盒外标记齿轮组图号，齿轮表面须按图示部位用电蚀法标记零件号和供货商代码，字高约0.25。
        攻丝后，去除螺纹孔内的铁屑。