|
本帖最后由 ryouss 于 2017-3-4 14:42 编辑
; U7 E) ^3 y& l1 W& ?% v; R& `% u0 ?$ J% i+ `7 D) a3 t; O9 l
用 Select Case 做篩選循環,
( ] l- J8 @0 G+ n不過如下宏只是做零件,裝配件及工程圖的叫出再關閉,沒實質意義.8 N! V& M; U6 u8 U: b% r
% y2 X1 h% f# H: I6 A& P7 }$ _
1 I0 H7 R% c+ d$ d4 K
; n8 u* v) Y }5 t6 T5 A- '' n* h) Z9 t* f0 ~- \( `: T
- ' 在某文件路徑下批量開零件,裝配件及工程圖
/ V w& w2 |- W( L! b, {) k - ' sc liang 2017/3/4
9 p R c9 t7 q; E7 W - ' 測試版 2012 sp4 e& T+ R. ~2 ~, j! b3 k, ?8 I! ^) U! P
- '
- f7 E) y5 _) V) P* K - Dim nErrors As Long* r7 j6 B7 _" c% [0 `
- Dim nWarnings As Long# ]- n1 I" I5 q9 x3 O
9 B2 a1 t1 o, \# c2 D h' T- Sub Test()8 y2 V2 v3 k8 m2 O! z6 M
- Set swApp = Application.SldWorks
0 o& Q9 ~, |5 f& t4 E - Set swModel = swApp.ActiveDoc6 I1 t1 x; Q$ p6 d/ |5 j* K9 F( l( u
- path = "D:\Project" '存檔路徑! T) r( P$ k5 b* Y* X. K# I
- sFileName = Dir(path & "*.sld*") '取出SW文件
% W) A9 S/ M/ p - '循環開檔* V* B: r' j# Y/ a2 q4 v
- Do Until sFileName = ""
0 A9 b' \ B4 R2 R3 D - Type_ = Right(sFileName, 3) '取得SW文件擴展名後三位) y' e: G. K2 ?: B y
- Select Case Type_ '判定SW文件型式
% e1 J' A D) q: K' u$ c - '開零件檔並存檔3 M/ `1 d) V2 ]
- Case "PRT"1 C% o& e& p& x: Z; \& Q% r
- Set swModel = swApp.OpenDoc6(path + sFileName, swDocPART, swOpenDocOptions_Silent, "", nErrors, nWarnings)6 u5 v. f" ]- P! c. }
- Set Part = swApp.ActiveDoc" `- X- w- U2 R3 i6 d2 H; l
- Part.Save
4 V+ |0 a$ ?9 C5 @! A6 M* N1 b W - '開組件檔/ ]& o! ?, k4 s) y+ a% O& R% Y$ z# G
- Case "ASM"
/ v0 r0 d/ i8 z1 u: d( x - Set swModel = swApp.OpenDoc6(path + sFileName, swDocASSEMBLY, swOpenDocOptions_Silent, "", nErrors, nWarnings)
% Z6 m; f. [7 g. G+ m4 k* G% [ - '開工程圖 - r3 E: S' ~: W; {) {
- Case "DRW"& M6 ~0 D! g2 @; P+ m% Z
- Set swModel = swApp.OpenDoc6(path + sFileName, swDocDRAWING, swOpenDocOptions_Silent, "", nErrors, nWarnings)( N5 b5 }! w0 V# Y+ t, F& ?
- + [6 T9 h) X: v+ Q7 @
- End Select
; f- o: V, B& U, ?: } - Set swModel = Nothing
' ]# D& M- i7 ~2 r4 S - swApp.CloseDoc (sFileName)
0 }- L9 E( e; V$ k u - sFileName = Dir '同路徑取出下個SW文件檔名
9 K# L1 }) m$ J& r" n; k- S- b6 | - Loop! P) S% {- p$ Q
- End Sub
复制代码 |
|