|
本帖最后由 ryouss 于 2017-3-4 14:42 编辑
! l' _) S% G4 j7 H( e& T; X8 p8 w4 W, K! u, S9 ?' Y
用 Select Case 做篩選循環,4 h$ u$ I4 @4 U
不過如下宏只是做零件,裝配件及工程圖的叫出再關閉,沒實質意義.
2 q9 n1 ^: `& n+ k) l$ N; r7 ` B# Q+ ]5 H% t, v
" {, G `- A6 X( E& P% W- W' x/ ^" F6 A9 S4 C: q" _( }8 o7 u( I( R I
- '
$ O5 H7 B- W4 m: b - ' 在某文件路徑下批量開零件,裝配件及工程圖
9 u& S: b/ B0 j9 c. J - ' sc liang 2017/3/4
' N1 w2 @! U3 }$ G5 f9 R5 t0 W - ' 測試版 2012 sp40 L2 o- u9 N2 Z1 I' L+ m6 S
- '
/ W/ a3 k$ j$ o+ Z) V/ M3 @% L6 ]! C - Dim nErrors As Long3 y5 ^- P( Y L2 B3 z3 }. w9 d# k
- Dim nWarnings As Long9 O- u' p/ [ L; _/ g# H
. _1 y9 G& w Q+ M U: ^- Sub Test()+ C) D. o' V6 c* e( N! I
- Set swApp = Application.SldWorks
7 T( p) S1 b& j - Set swModel = swApp.ActiveDoc5 V6 J" L, w5 m
- path = "D:\Project" '存檔路徑# A8 u- G1 J& S- o% w5 o, Z Q4 x
- sFileName = Dir(path & "*.sld*") '取出SW文件
: i; j6 X6 b: W5 B Z - '循環開檔
# Z' F3 ?2 p( b9 { - Do Until sFileName = "". n& e) M; i- G9 `, T4 c
- Type_ = Right(sFileName, 3) '取得SW文件擴展名後三位0 I$ f1 P3 T4 j k: l/ }; @- ^
- Select Case Type_ '判定SW文件型式* |* t6 ?5 f" Z
- '開零件檔並存檔% l2 \3 i% q6 V4 `' u" c
- Case "PRT"2 H! H! ~* B6 @2 {3 t5 W" Z
- Set swModel = swApp.OpenDoc6(path + sFileName, swDocPART, swOpenDocOptions_Silent, "", nErrors, nWarnings), \' G! p C" k+ B; E9 ^
- Set Part = swApp.ActiveDoc
# ?4 W( G) l1 C, W/ t8 s - Part.Save; ]0 n1 I! s& Y/ m5 @. r, c
- '開組件檔% @6 g. \& \) ?1 t
- Case "ASM"' K2 {% Z+ f; i0 I Q/ }; f
- Set swModel = swApp.OpenDoc6(path + sFileName, swDocASSEMBLY, swOpenDocOptions_Silent, "", nErrors, nWarnings)
$ o8 I1 F1 o/ C* R: o - '開工程圖
/ V+ m+ ~0 F4 R' T# D9 y$ o; J) y0 Y - Case "DRW", h; ~$ P- j \' R/ V
- Set swModel = swApp.OpenDoc6(path + sFileName, swDocDRAWING, swOpenDocOptions_Silent, "", nErrors, nWarnings)
1 G4 _$ _7 U8 a* z& [% K7 | - . [8 k: W( m/ d5 P1 I
- End Select% l; ~) f: _* k0 Z7 H
- Set swModel = Nothing9 R7 r* O4 R" c
- swApp.CloseDoc (sFileName)
' z$ T% j6 \8 n/ K a - sFileName = Dir '同路徑取出下個SW文件檔名
# ^. W" I3 X& r; }8 Y% u1 U - Loop& X/ [/ ~7 \( j5 f9 f- D
- End Sub
复制代码 |
|