扳手
4 ~" R9 y* ^ x. Z, @, B* [ | wrench |
板簧
! A; q) J, R2 I; e- s. `# l3 ^ | flat leaf spring |
半圆键 9 O9 p/ h1 J4 z7 Q
| woodruff key |
变形 : P& K4 t* t- `9 Y1 k( y
| deformation |
摆杆 2 o# u& u! ?2 s1 y% P5 w" l
| oscillating bar |
摆动从动件
9 j1 p$ l7 E6 `; A/ ]# l4 | | oscillating follower |
摆动从动件凸轮机构 ! A6 Z9 b; `4 ~0 C! a
| cam with oscillating follower |
摆动导杆机构 ) L' J* R9 r8 o/ O9 z4 T+ M
| oscillating guide-bar mechanism |
摆线齿轮 / [0 ?& ]- s! u) c. h" j4 Y
| cycloidal gear |
摆线齿形
% Z! @! M2 j& P! v1 K/ Y | cycloidal tooth profile |
摆线运动规律 & d8 y3 t+ T, G
| cycloidal motion |
摆线针轮
5 G" g" M, C# b- _ | cycloidal-pin wheel |
包角
( w L" h% w6 |# j" p | angle of contact |
保持架 ; z! T4 G. ?* M3 f. y- o
| cage |
背对背安装 ; C7 }8 a$ L7 ]7 `
| back-to-back arrangement |
背锥 2 B3 z3 r& {0 k" f) u; ?( x) M
| back cone ； normal cone |
背锥角
5 k, }7 g( A; |$ w, w0 | | back angle |
背锥距
. x9 l$ D& W7 g0 }0 L8 _ | back cone distance |
比例尺
9 T- x2 a2 R( T1 a% ~ | scale |
比热容
# C% f/ r P8 D% [7 M( p% q8 R | specific heat capacity |
闭式链 " L" q2 H$ q0 v2 w
| closed kinematic chain |
闭链机构
4 \9 H8 a+ p" f* U* ` | closed chain mechanism |
臂部
7 l8 o* z& H4 W' v0 ? | arm |
变频器 " f0 |3 G3 L1 V2 X- `- H
| frequency converters |
变频调速 : A, Y+ k" u1 [
| frequency control of motor speed |
变速
) y; @5 R7 t1 W Q | speed change |
变速齿轮 ( }) J( p! ^- N; W" }% }) q
| change gear ; change wheel |
变位齿轮
7 J C* O/ {, A! V( I | modified gear |
变位系数 " `: b+ G3 m- A: {/ I6 P' g
| modification coefficient |
标准齿轮 + p8 r; c8 b. y, H9 b0 C- {. `
| standard gear |
标准直齿轮 7 R, Y" [. [2 c+ }; }$ ~8 o
| standard spur gear |
表面质量系数
; Q3 v; M, y9 e* k0 T | superficial mass factor |
表面传热系数 : t, L6 c5 a3 c0 H! g
| surface coefficient of heat transfer |
表面粗糙度 6 E3 Z' u' U) d' b w. N
| surface roughness |
并联式组合
' O, n3 ?0 w5 c8 ^; g8 L' U | combination in parallel |
并联机构 $ E' k2 d: v! ~7 I% N& n @ E
| parallel mechanism |
并联组合机构 + G7 v4 w' T9 g1 O: m- [9 Z5 L% g
| parallel combined mechanism |
并行工程
0 U/ ~2 K5 F9 ?/ z; b | concurrent engineering |
并行设计 # ?# d; x$ |: d' h7 I7 s0 e
| concurred design, CD |
不平衡相位
4 c/ E8 ?, B! |1 z0 s | phase angle of unbalance |
不平衡 : e+ m' g" h4 W6 _
| imbalance (or unbalance) |
不平衡量 % R& G5 c) ^ W0 E4 x
| amount of unbalance |
不完全齿轮机构 7 j4 q: U3 ~2 E' N
| intermittent gearing |
波发生器
" z5 g c7 A& Z1 N' R# B | wave generator |
波数 ! l& j" x* V& V d0 u
| number of waves |
0 N' y$ W, C9 o
|
8 H" c. q& |# x* _6 o: I5 a
3 l2 j) E- y! w) F! V |
发表于 2009-4-9 16:56:46
QQ好友和群
收藏
淘帖
问题专业，描述清楚
伸手党/灌水/看不懂
发表于 2009-4-9 20:05:05
楼主
